Dell™ OptiPlex™ 745 User's Guide
Dell Diagnostics
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. |
When to Use the Dell Diagnostics
If you experience a problem with your computer, perform the checks in this section and run the Dell Diagnostics before you contact Dell for technical assistance.It is recommended that you print these procedures before you begin.
NOTICE: The Dell Diagnostics works only on Dell™ computers. |
Start the Dell Diagnostics from either your hard drive or from the Drivers and Utilities CD (an optional CD also known as the ResourceCD). See Starting the Dell Diagnostics From Your Hard Drive or Starting the Dell Diagnostics From the Drivers and Utilities CD (Optional) for more information.
Starting the Dell Diagnostics From Your Hard Drive
NOTE: If you see a message stating that no diagnostics utility partition has been found, run the Dell Diagnostics from your optional Drivers and Utilities CD. See Finding Information for more information about the optional Drivers and Utilities CD. |
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.
- When the boot device list appears, highlight Boot to Utility Partition and press <Enter>.
- When the Dell Diagnostics Main Menu appears, select the test you want to run (see Dell Diagnostics Main Menu).
Starting the Dell Diagnostics From the Drivers and Utilities CD (Optional)
When the DELL logo appears, press <F12> immediately.
If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer and try again.
NOTE: The next steps change the boot sequence for one time only. On the next start-up, the computer boots according to the devices specified in system setup. |
- When the boot device list appears, highlight IDE CD-ROM Device and press <Enter>.
- Select the IDE CD-ROM Device option from the CD boot menu.
- Select the Boot from CD-ROM option from the menu that appears.
- Type 1 to start the Drivers and Utilities CD menu.
- Type 2 to start the Dell Diagnostics.
- Select Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your computer.
- When the Dell Diagnostics Main Menu appears, select the test you want to run (see Dell Diagnostics Main Menu).
Dell Diagnostics Main Menu
- After the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want.
- If a problem is encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem description and follow the instructions on the screen.
If you cannot resolve the error condition, contact Dell (see Contacting Dell).
NOTE: The Service Tag for your computer is located at the top of each test screen. If you contact Dell, technical support will ask for your Service Tag. Your computer's Service Tag is listed in the System Info option in system setup. See System Setup for more information. |
- If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information.
- When the tests are completed, if you are running the Dell Diagnostics from the Drivers and Utilities CD, remove the CD.
- Close the test screen to return to the Main Menu screen. To exit the Dell Diagnostics and restart the computer, close the Main Menu screen.
System Lights
Your power button light and hard-drive light may indicate a computer problem.
Power Light
|
Problem Description
|
Suggested Resolution
|
---|---|---|
Solid green | Power is on, and the computer is operating normally. On the desktop computer, a solid green light indicates a network connection. | No corrective action is required. |
Blinking green | The computer is in a power-saving mode (Microsoft® Windows® XP). | Press the power button, move the mouse, or press a key on the keyboard to wake the computer. |
Blinks green several times and then turns off | A configuration error exists. | Check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights). |
Solid yellow | The Dell Diagnostics is running a test, or a device on the system board may be faulty or incorrectly installed. | If the Dell Diagnostics is running, allow the testing to complete. If the computer does not boot, contact Dell for technical assistance (see Contacting Dell). |
Blinking yellow | A power supply or system board failure has occurred. | See Power Problems. |
Solid green and a beep code during POST | A problem was detected while the BIOS was executing. | See Beep Codes for instructions on diagnosing the beep code. Also, check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights). |
Solid green power light and no beep code and no video during POST | The monitor or the graphics card may be faulty or incorrectly installed. | Check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights). See Video and Monitor Problems. |
Solid green power light and no beep code but the computer locks up during POST | An integrated system board device may be faulty. | Check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights). If the problem is not identified, contact Dell for technical assistance (see Contacting Dell). |
Diagnostic Lights
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. |
If the POST portion of system boot completes successfully, all four lights display solid green. If the computer malfunctions during the POST process, the pattern displayed on the LEDs may help identify where in the process the computer halted.
NOTE: The orientation of the diagnostic lights may vary dependent upon the computer type. The diagnostic lights can appear either vertical or horizontal. |
Light Pattern
|
Problem Description
|
Suggested Resolution
|
---|---|---|
| The computer is in a normal "off" condition, or a possible pre-BIOS failure has occurred. The diagnostic lights are not lit after the computer successfully boots to the operating system. | Plug the computer into a working electrical outlet and press the power button. |
| A possible BIOS failure has occurred; the computer is in the recovery mode. | Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer. |
| A possible processor failure has occurred. | Reinstall the processor and restart the computer. |
| Memory modules are detected, but a memory failure has occurred. |
|
| A possible graphics card failure has occurred. |
|
| A possible floppy or hard drive failure has occurred. | Reseat all power and data cables and restart the computer. |
| A possible USB failure has occurred. | Reinstall all USB devices, check cable connections, and then restart the computer. |
| No memory modules are detected. |
|
| Memory modules are detected, but a memory configuration or compatibility error exists. |
|
| A failure has occurred. This pattern also displays when you enter system setup (see Entering System Setup) and may not indicate a problem. |
|
| After POST is complete, all four diagnostic lights turn green briefly before turning off to indicate normal operating condition. | None. |
Beep Codes
Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. This series of beeps, called a beep code, identifies a problem. One possible beep code (code 1-3-1) consists of one beep, a burst of three beeps, and then one beep. This beep code tells you that the computer encountered a memory problem.If your computer beeps during start-up:
- Write down the beep code on the Diagnostics Checklist.
- Run the Dell Diagnostics to identify a more serious cause (see Dell Diagnostics).
- Contact Dell for technical assistance (see Contacting Dell).
Error Messages
Fill out the Diagnostics Checklist as you complete these checks.CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. |
A filename cannot contain any of the following characters: \ / : * ? " < > | — Do not use these characters in filenames. |
A required .DLL file was not found — The program that you are trying to open is missing an essential file. To remove and then reinstall the program: |
Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support — Contact Dell (see Contacting Dell) and report the checkpoint code (nnnn) to the support technician. |
Alert! Air temperature sensor not detected — For any computer type except the ultra small form-factor computer, ensure that all cables are securely fastened to the I/O panel and to the system board and reboot your computer. If this does not resolve the problem or if you have an ultra small form-factor computer, contact Dell (see Contacting Dell). |
Attachment failed to respond — See Drive Problems. |
Bad command or file name — Ensure that you spelled the command correctly, put spaces in the proper place, and used the correct pathname. |
Bad error-correction code (ECC) on disk read — See Drive Problems. |
Controller has failed — See Drive Problems. |
Data error — See Drive Problems. |
Decreasing available memory — See Lockups and Software Problems. |
Diskette drive 0 seek failure — See Drive Problems. |
Diskette read failure — See Drive Problems. |
Diskette subsystem reset failed — Run the Dell Diagnostics (see Dell Diagnostics). |
Diskette write protected — Slide the write-protect notch on the floppy disk to the open position. |
Drive not ready — Put a floppy disk in the drive. |
Gate A20 failure — See Lockups and Software Problems. |
Hard-disk configuration error — Hard-disk controller failure — Hard-disk drive failure — Hard-disk drive failure — See Drive Problems. |
Insert bootable media — Insert a bootable floppy disk or CD. |
Invalid configuration information - please run SETUP program — Enter system setup and correct the computer configuration information (see Entering System Setup). |
Keyboard failure — See Keyboard Problems. |
Memory address line failure at address, read value expecting value — See Lockups and Software Problems. |
Memory allocation error — |
Memory data line failure at address, read value expecting value — Memory double word logic failure at address, read value expecting value — Memory odd/even logic failure at address, read value expecting value — Memory write/read failure at address, read value expecting value — Memory size in CMOS invalid — See Lockups and Software Problems. |
No boot device available —
|
No boot sector on hard-disk drive — Enter system setup and ensure that the computer configuration information for the hard drive is correct (see Entering System Setup). |
No timer tick interrupt — Run the Dell Diagnostics (see Dell Diagnostics). |
Non-system disk or disk error — Replace the floppy disk with one that has a bootable operating system or remove the floppy disk from drive A and restart the computer. |
Not a boot diskette — Insert a bootable floppy disk and restart your computer. |
Not enough memory or resources. Close some programs and try again — Close all windows and open the program that you want to use. In some cases, you might have to restart your computer to restore computer resources. If so, run the program that you want to use first. |
Operating system not found — Contact Dell (see Contacting Dell). |
Plug and Play Configuration Error —
|
Read fault — Requested sector not found — Reset failed — See Drive Problems. |
Sector not found — |
Seek error — See Drive Problems. |
Shutdown failure — Run the Dell Diagnostics (see Dell Diagnostics). |
Time-of-day clock stopped — Time-of-day not set-please run the System Setup program — Enter system setup (see Entering System Setup) and correct the date or time. If the problem persists, replace the battery (see Replacing the Battery). |
Timer chip counter 2 failed — Run the Dell Diagnostics (see Dell Diagnostics). |
Unexpected interrupt in protected mode — Run the Dell Diagnostics (see Dell Diagnostics). |
WARNING: Dell's Disk Monitoring System has detected that drive [0/1] on the [primary/secondary] EIDE controller is operating outside of normal specifications. It is advisable to immediately back up your data and replace your hard drive by calling your support desk or Dell — If no replacement drive is immediately available and the drive is not the only bootable drive, enter system setup (see Entering System Setup) and change the appropriate drive setting to None. Then remove the drive from the computer. |
Write fault — Write fault on selected drive — See Drive Problems. |
<drive letter>:\ is not accessible. The device is not ready — The selected drive cannot read its medium. Depending on its medium type, insert a floppy, CD, or Zip disk into the drive and try again. |
Resolving Software and Hardware Incompatibilities
If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use Device Manager or the Hardware Troubleshooter to resolve the incompatibility.Microsoft® Windows® XP
To resolve incompatibilities using Device Manager:- Click the Start button and click Control Panel.
- Click Performance and Maintenance and click System.
- Click the Hardware tab and click Device Manager.
- In the Device Manager list, check for devices that are incorrectly configured.
Incorrectly configured devices are indicated by a yellow exclamation point (!) or a red X if the device has been disabled.
The Device status area in the Properties window reports the devices that need to be re-configured.
- Reconfigure the devices or remove the devices from the Device Manager. See the documentation that came with the device for information on configuring the device.
- Click the Start button and click Help and Support.
- Type hardware troubleshooter in the Search field and click the arrow to start the search.
- Click Hardware Troubleshooter in the Search Results list.
- In the Hardware Troubleshooter list, click I need to resolve a hardware conflict on my computer, and click Next.